Fix There was a Problem Resetting Your PC Windows 10

Sponsored Links

About ‘There was a problem resetting your PC’ issue

 

Whenever something goes wrong while booting system, Windows first runs into Automatic Repair wizard and fixes the issues automatically. And if it failed, you have to Refresh or Reset the machine. But at most times, Windows 10 reset failed and generated error messages as follows.

If you try to attempt for Refresh, you will see the error message ‘There was a problem refreshing your PC. No changes were made ‘.
There was a problem resetting your PC

How to Fix There was a problem resetting your PC error

1. Use Command Prompt

Checking system files using Command Prompt is a good option to fix this dreaded error. Follow these steps in order to do so:

Step-1: Firstly click the Power button from Start menu. Then while holding the Shift key, click Restart.

Restart

Step-2: Now follow this path: Click Troubleshoot Advanced options Command Prompt.

Command Prompt

Step-3: Then select your administrator account and enter the password (if you have set one before). Afterwards, click on Continue to proceed.

administrator account

33.jpg

Step-4: Once the Command Prompt window opens up, type the following commands in the window and hit Enter after each command:

cd %windir%\system32\config
ren system system.001
ren software software.001

4-1

Step-5: After doing this, close the command prompt window. You will be taken back to bootoptions page. Just click on Continue to boot into your Windows 10.

5

Step-6: Try resetting your PC now.

You will be able to reset your PC now without any difficulty. However, if the problem still persists, move down to the next method.

2. Use Recovery USB

If Command Prompt fails to fix the error, you can use Recovery USB to recover your computer. Follow these steps in order to do so:

Step-1: Firstly, insert an empty USB Flash drive(16GB or 32GB recommended) into your PC.

Step-2: Now type recovery drive in the search bar from Start menu. Then click on Create a recovery drive from the list of results. Click Yes when User Account Control prompts.

Step-3: Recovering your PC from a drive will remove all the present files and apps, so you should select to tick on Back up system files to the recovery drive in this step to back up your data. Afterwards, click Next.

Step-4: Now select your USB drive and click Next.

Step-5: Then click Create to make a recovery drive. Once the process is complete, click Finish.

Step-6: Afterwards, reboot your Windows 10. Press the specific key, like F12 or any other key your PC suggests to enter into the boot options page. Continue with choosing to boot from your USB recovery drive.

Step-7: Finally, click Recovery from a drive and then follow the instructions appearing on your screen.

3. Clean Install Windows

If nothing worked out for you yet, you should just consider doing a clean installation of Windows. Follow these steps in order to do so:

Sponsored Links

Step-1: Insert the Windows installation media device and start your PC.

Step-2: Now press the key to boot from the installation media (USB or DVD) and format the drive. Then reinstall your windows by following the instructions appearing on the screen.

This method shall surely fix There was a problem resetting your PC windows 10 error from your PC.

Tag : Fix There was a Problem Resetting Your PC Windows 10

How to Fix Steam Not Open in Windows 7/8/10

Here is a list of 3 ways along with their step-wise guides to solve the steam not opening in Windows 7/8/10 problem. You can try any of the methods selectively, or you can try them all one after another until you find the one working perfectly for you.

Sponsored Links

Ways to Fix Steam not opening in Windows 7/8/10

How to Fix Steam Not Opening in Windows

#Method 1 : Use Task Manager to Fix Steam Won’t Open

1. You hold Ctrl+Shift+Esc to open Task Manager.
2. Scroll to Steam Client Bootstrapper
3. End task.
4. Try opening steam again.
5. If fail you restart ( or log off ) your computer and open steam again .

Steam Client Bootstrapper

#Method 2 : Update Windows to Fix Steam Won’t Open ( for windows 10 )

Step-1: Go to the search bar from Start and type update. From the list of results, click on Check for updates.

Check for updates

Step-2: In the Windows Update window, click on Check for updates button. Windows will then look for the available updates.

Check for updates button

Step-3: If an update is available, install it and reboot your PC. If Windows tells Your device is up to date after checking, skip to the next method right now.

#Method 3 : For the people who have this issue and don’t have a restore point ( for windows 7 )

“If you run it in compatibility mode it seems to work, including starting a game.
(Right click Steam -> Properties -> Compatibility tab -> Run this program in compatibility mode for -> Windows 7)

What has likely happened, is we all updated Windows 7 to Windows 7 Service pack 1. There is some sort of incompatibility without reinstalling I assume, so you must run it in compatibility mode for Windows  7 without the service pack. ”

Tag : steam won t open , steam won t open windows 7 , steam won t open windows 8 , steam won t open windows 10

How to Fix KMode Exception Not Handled

Blue Screen of Death (BSoD) errors are the most dreaded kind of errors for Windows users. These errors turn the monitor screen into a blue mess of error messages and inhibit the functioning. BSoD errors lead to system crashing and turning the entire screen to blue in color with several lines of error code. There are several different types of BSoD errors that Windows users face. One fearful BSoD error is KMODE Exception Not Handled. In this article, I will demonstrate you how to fix KMode Exception Not Handled Error in Windows 7 , 8 , 10 permanently in a very simple manner

How to Fix KMode Exception Not Handled

What is KMODE_EXCEPTION_NOT_HANDLED?

In Windows or all the modern era Operating Systems, there is a division between the code operating which is “User Mode” and the other one is known as “Kernel Mode”. While at the other side, all the computer processors have different modes of operation which are termed as “Rings.” Any particular type of ring has its own instructions and memory available to run the certain type of code.

Let’s take a look at the Intel CPU’s, it has four rings where the first one is named “Ring 0” (also known as kernel mode). This is the one in charge of operations and has full access to use every available resource. It is the mode in which the Windows Kernel runs.

When the Windows Operating System is just about to boot, the Windows Kernel is started. It runs in Kernel mode and creates up Paging and the Virtual Memory. Usually, most of the programs launch in the Kernel mode. When they overwrite each other’s memory, it results in some crashes and even in the crashing of the entire system.

This is known as KMODE_EXCEPTION_NOT_HANDLED, a  type of Blue Screen Of Death Error with the Bug Check Error Code value of 0x0000001E.

Reason Behind KMODE Exception Not Handled Error

 

The major reason behind this error to appear on your monitor’s Screen is that a Kernel Mode Program is causing an exception, which the error handler is not able to identify. The exception produced by a Kernel Mode program is not handled well by the error handler and this is indicated by the STOP error 0x0000001E. It may also indicate that some driver complications are faced by the system. In a very simple language, it is possible that your computer’s Windows, Drivers, Registry or maybe some Software is corrupted, resulting in this issue. A Faulty RAM or an outdated or corrupted driver is the most common cause of this issue. However, the list of reasons is still vast and we don’t need to learn about them all.

How to Fix KMODE EXCEPTION NOT HANDLED in Windows 7/8/8.1/10

1. Turning OFF Fast Startup
This is the simplest and the most working method available to fix the KMODE Exception Not Handled error. Follow these steps in order to turn off Fast Startup on your PC:

Step-1: Firstly, go to Control Panel. Then locate and click on System and Security and then on Power Options.

Power Options

Step-2: Now Select Choose what power buttons do.
Step-3: Then Click on Change settings that are currently unavailable.

Computer-Power-Button.jpg

Step-4: Finally, just Uncheck the box next to ‘Turn on fast start-up’ and Save the changes.

Turn on fast start-up

This might have solved your problem. You can now continue to use your PC without being annoyed by the BSoD. If in case the Blue Screen is still appearing on your screen, try the next mentioned method.

2. Update Drivers

Outdated or corrupt drivers are a common cause for the KMODE Exception Not Handled issue. Therefore, updating them will help to resolve the issue. Follow these steps in order to update the device drivers:

Step-1: Firstly shut down your system and Boot it into Safe Mode. You can do so by pressing the F8 key while Windows is starting up.

NOTE: Booting into Safe Mode is essential as Blue Screen won’t let you complete this procedure in Normal Mode. If you are facing any issue Booting in Safe Mode, just Google out the procedure for your OS.

Step-2: After the Windows has started in Safe Mode, press the Windows + X key simultaneously. From the appearing Sidebar, choose Device Manager.

Device Manager

Step-3: In the Device Manager, locate and click on Other Devices to expand it. Now find and right-click on Unknown Device, and then click on Update Driver Software… option.

Unknown Device

 

Step-4: In the next screen, click on “Search automatically for updated driver software.”

Search automatically for updated driver software

 

Step-5: Wait patiently till the drivers are updated. Afterwards, restart your computer.

This surely has fixed the issue on your PC. However, if the problem still persists, move down to the next method and resolve your issue using it.

After following these steps you won’t be facing KMode Exception Not Handled during Install or overclock error.

Sponsored Links

Tag : kmode exception not handled , kmode exception not handled windows 10 , kmode exception not handled windows 8 , kmode exception not handled windows 7

How to fix Razer Synapse Not Working on Windows 7/8/10

Computer enthusiasts are well aware of Razer and their products. Razer mouse and Razer keyboard are the two most popular Razer products. The best aspects of Razer products are their versatility and reliability. If you are a frequent Razer products user, you must have used Razer Synapse. It is Razer’s cloud-based unified configuration software to manage all the other Razer devices. However, sometimes Razer Synapse might create some issues and stops working. The scenario gets really frustrating then. Therefore, in this article, I will demonstrate How to Fix Razer Synapse not Working in Windows 7/8/10 in some very simple ways.

After this article you will be able to fix the following errors:

  1. Razer Synapse Not Working
  2. Razer Synapse Won’t Open
  3. Razer Synapse Not Responding
  4. Razer Synapse Network Not Available

And a lot more.

Introduction: Razer Synapse

Razer Synapse is Razer Inc.’s cloud-based unified configuration software that allows you to rebind controls or assign macros to any of your Razer devices. Additionally, it saves all your settings automatically to the cloud.

Basically, it helps you to manage all other Razer devices that you use like Razer mouse, Razer keyboard, etc. It helps you to avoid boring device configurations when you arrive at LAN parties or tourneys, as you can retrieve them from the cloud, and own them right away.

Razer Synapse’s another advantage is that it keeps your devices in optimal condition by automatically updating and downloading driver and firmware updates, as they become available.

The notable thing is that Razer Synapse is not a compulsory software for your Razer hardware to work, but it is advisable to use Razer Synapse if you wish to unlock your Razer peripheral’s full potential.

Razer Synapse Not Working Error

As I explained above, Razer Synapse is a very beneficial thing for Razer hardware users. However, sometimes Razer Synapse starts creating conflicts. As Razer Synapse manages all the other Razer devices, the situation gets really annoying when it stops working properly. This simply ruins the overall user experience. There are certain reasons for Razer Synapse not working properly but the major one is outdated or corrupted drivers. Other reasons include corrupt system files, virus or malware or just a bad internet connection. In case of a bad internet connection, Razor Synapse not working can be solved easily by switching to a good internet connection. However, if the problem is caused due to any other reason, you must fix Razer Synapse not Working problem manually. If this is the case, let’s move further to the working methods to fix Razer Synapse not working problem.

3 Methods to Fix Razer Synapse Not Working

There are 3 methods available to fix the Razer Synapse not working problem. You don’t need any special tools or information to use these. Just follow the step-wise guide that is present below each method.

You can try any of the methods selectively, or you can try them one by one. Let’s proceed to the methods to fix Razer Synapse not working problem.

Introduction: Razer Synapse

Razer Synapse is Razer Inc.’s cloud-based unified configuration software that allows you to rebind controls or assign macros to any of your Razer devices. Additionally, it saves all your settings automatically to the cloud.

Basically, it helps you to manage all other Razer devices that you use like Razer mouse, Razer keyboard, etc. It helps you to avoid boring device configurations when you arrive at LAN parties or tourneys, as you can retrieve them from the cloud, and own them right away.

Razer Synapse’s another advantage is that it keeps your devices in optimal condition by automatically updating and downloading driver and firmware updates, as they become available.

The notable thing is that Razer Synapse is not a compulsory software for your Razer hardware to work, but it is advisable to use Razer Synapse if you wish to unlock your Razer peripheral’s full potential.

Razer Synapse Not Working Error

As I explained above, Razer Synapse is a very beneficial thing for Razer hardware users. However, sometimes Razer Synapse starts creating conflicts. As Razer Synapse manages all the other Razer devices, the situation gets really annoying when it stops working properly. This simply ruins the overall user experience. There are certain reasons for Razer Synapse not working properly but the major one is outdated or corrupted drivers. Other reasons include corrupt system files, virus or malware or just a bad internet connection. In case of a bad internet connection, Razor Synapse not working can be solved easily by switching to a good internet connection. However, if the problem is caused due to any other reason, you must fix Razer Synapse not Working problem manually. If this is the case, let’s move further to the working methods to fix Razer Synapse not working problem.

3 Methods to Fix Razer Synapse Not Working

There are 3 methods available to fix the Razer Synapse not working problem. You don’t need any special tools or information to use these. Just follow the step-wise guide that is present below each method.

You can try any of the methods selectively, or you can try them one by one. Let’s proceed to the methods to fix Razer Synapse not working problem.

1. Re-install Device Drivers

Drivers are the major cause of the Razor Synapse not working problem. In this method, I will show you how to remove and re-add the devices to re-install their devices. This will eventually resolve the issue. Follow these steps in order to solve the Razer Synapse not working problem:

Step-1: Firstly, press & hold the Windows logo key + R key to trigger the Run dialog box. Type devmgmt.msc in it and then hit EnterDevice Manager will open up.

Step-2: Now find and click on Human Interface DevicesKeyboardsMice and other pointing devices sections to expand them.

Step-3: After that, right-click on each Razer device and then click on Uninstall device. Remember to select delete drivers as well when uninstalling.

Step-4: Afterwards, go to the Search bar from the Start menu and type programs and then click on Apps & features from the resultant list.

Step-5: Locate Razer Synapse there and click on Uninstall.

Step-6: Now remove all your Razer devices from the computer. Keep them disconnected for 5 minutes. Then plug them back to the computer.

Step-7: Windows will then automatically install all the required device drivers. Also, Razer Synapse will also appear. Let it download and then install. Finally, check if Razer Synapse is working fresh and fine now.

2. Re-installing Software

Re-installing the Razor Synapse is possibly the best and simplest way to resolve the Razer Synapse not working issue. Follow these steps in order to solve the problem:

Step-1: Firstly, press & hold the Windows logo key + R key to trigger the Run dialog box. Type “appwiz.cpl” in it and hit EnterPrograms and Features window will open up.

Step-2: Locate Razor Synapse and Razor Coreright-click on them and then click on Uninstall.

 

Step-3: Navigate to C:\Program Files (x86)\Razer and C:\ProgramData\Razer directories and delete all the files present there. Make sure to unhide the files first and then delete them (click on View and check the Hidden items box).

Step-4: Restart your computer after deleting the files.

Step-5: Press & hold the Windows logo key + R key to trigger Run dialog box. Type devmgmt.msc in it and then hit EnterDevice Manager will open up.

Step-6: In the Device Manager, locate all the Razer devices and right-click on them. Then select Uninstall device and remember to check the Delete the driver software for this device box while deleting.

Step-7: Unplug all the Razer devices from the computer. Keep them disconnected for about 5 minutes and then plug them back again. Windows will then install their drivers automatically again.

Step-8: Turn off the firewall and antivirus software. Install the latest version of .NET Framework from here.

Step-9: Download Razer Synapse from the official website and check if the problem is solved. However, Razer Synapse will also be installed automatically along with the drivers.

3. Update Windows

Updates are provided to improvise the overall functioning, performance, and security of the system. Bugs are also fixed in the newer updates. Follow these steps in order to update Windows:

Step-1: Firstly go to Control Panel and then to System and Security.

Step-2: Now click on Windows Updates section.

Step-3: Then just click on Check for updates and let Windows find and install (if available) updates.

Conclusion

These were the 3 best & easy methods on How to fix Razer Synapse not working or won’t open problem without any struggle. If you applied the suitable method properly, you would be using Razer Synapse and other Razer devices smoothly. One more way to get rid of the Razer Synapse not working problem is by disabling Razer Surround.

Source : https://windowsfish.com/fix-razer-synapse-not-working/

How to Set Screen Savers on Windows 7/8/10

Screensavers are a visual treat and there are plenty available all over the Internet.. It gets activated when the computer is not in use for a particular period of time. The idea behind this originally was to prevent phosphor burn-in on Cathode Ray Tube and Plasma monitors. But since now most of us use LCD monitors, they are used mainly for entertainment or security purposes.

How to Set Screen Savers on Windows 7/8

  1. Open Screen Saver Settings by right click on destop , choose Personalize

  2. Under Screen Saver, in the drop-down list, click the screen saver you want to use.
  3. Click Preview to see what your chosen screen saver will look like.
  4. Click OK.

Screen Savers on Windows 78

If you want disable the screen saver on windows 7/8 you do steps :

1. Right click on the desktop and select Personalization from the drop down menu.

2. In the personalization window, click on the Screensaver option (bottom right of window)

3. When the screensaver window opens, click the arrow to the right of the Screensaver dialogue box.

4. From the screensaver drop down menu, select None.

5. Press OK

6. Close down the personalization window.

7. Your screen saver is now disabled.

How to Set Screen Savers on Windows 10

#Method 1 : From destop 

  • You right click on destop , choose Personalize
  • Lockscreen > Screen Saver Setting

Screen Savers on Windows 10

#Method 2 : from Menu Start

  • Menu Start => Settings => Lock screen => Screen Saver Setting

Settings windows 10

#Method 3 : use Run

  • You use WIN+R => control desk.cpl,,@screensaver => enter

Run Screen Savers Windows 10

How to disable screen saver windows 10

Please follow the below steps to turn off screen saver and check if it works:

Step 1: Open Registry Editor. To do so, type Regedit in Start menu or taskbar search box and then press Enter key. Registry Editor can also be launched by typing Regedit in Run command box and pressing Enter key.

Step 2: In the Registry Editor, navigate to the following key:

HKEY_CURRENT_USER\Control Panel\Desktop

Step 3: On the right-side, look for the entry named ScreenSaveActive, double-click on it, and set the value to 1 (one) to enable screen saver and make it 0 (zero) to disable.

Note that if the ScreenSaveActive string value doesn’t exist, right-click on the empty area, click New, click String Value and name it ScreenSaveActive.

Tag : screensaver windows 10 , screensaver windows 7 , screensaver windows 8 , screensavers for windows , windows 10 screensaver settings

 

How to fix no internet secured windows 7/8/10

We generally use a secure Wi-Fi connection at our home/office. So, if we get a “No internet, Secured” error, this could be because of an invalid IP configuration. Maybe something changed the settings. here is what you can do.

#Method 1. Update your Network Adapter  software then restart them to fix no internet secured

This helps create a new connection to your Internet service provider (ISP). When you do this, everyone that is connected to your Wi-Fi network will be temporarily disconnected.

The steps you take to restart your modem and router can vary, but here are the general steps:

  1. Unplug the power cable for the router from the power source.
  2. Unplug the power cable for the modem from the power source.Some modems have a backup battery. So if you unplug the modem and lights stay on, remove the battery from the modem.
  3. Wait at least 30 seconds or so.If you had to remove the battery from the modem, put it back in.
  4. Plug the modem back into the power source. The lights on the modem will blink. Wait for them to stop blinking.
  5. Plug your router back into the power source.Wait a few minutes for the modem and router to fully power on. You can usually tell when they’re ready by looking at the status lights on the two devices.
  6. On your PC, try to connect again.

#Method 2 : Check the basics on your PC to fix no internet secured

  • Make sure Wi-Fi is turned on.
    1. On a laptop, open Windows Mobility Center by selecting the Start

      button and then selecting Control Panel Mobile PC Windows Mobility Center.

    2. Look in the Wireless Network section. If Wi-Fi is on, the button should say Turn wireless off.
  • Make sure the physical Wi‑Fi switch on your laptop is turned on. (An indicator light usually shows when it’s on.)
  • Check and make sure your PC isn’t in airplane mode.
  • Move closer to the router or access point if you can.
  • If you don’t see the network name at all, the router or access point might not be set to broadcast the network name. In this case, you’ll need to connect to it manually.
    1. Open Manage Wireless Networks by selecting the Start

      button, and then selecting Control Panel. In the search box, type wireless and then select Manage wireless networks.

    2. Select Add, and then select Manually create a network profile.
    3. Type the network information.
    4. If you want Windows to automatically connect when the network is in range, select the Start this connection automatically check box.
    5. Select the Connect even if the network is not broadcasting check box, select Next, and then select Close.
  • The network will be added to your list of networks and will be available to connect to when your computer is in range of the network. To connect to the network, follow these steps:
    1. Open Connect to a Network by selecting the network icon in the notification area.
    2. Select Unnamed Network, select Connect, and then type the network information. The network will be added to your list of networks and will be available to connect to in the future when your computer is in range of the network..

#Method 3 : Use the Network Troubleshooter to fix no internet secured

Let Windows try to help you fix the problem. Try running the Network troubleshooter to see if it can diagnose and fix the problem.

Open the Network troubleshooter by right-clicking the network icon in the notification area and then selecting Troubleshoot problems.

#Method 4 : Contact with Internet service provider to fix no internet secured

  1. Select the Start button

    . Type cmd in the search box, right-click cmd in the list, select Run as administrator, and then select Yes.

  2. At the command prompt, type ipconfig.Look for the IP address listed next to Default gateway. Write down that address if you need to. For example, 192.168.1.1.
  3. At the prompt, type ping <Default gateway> and press Enter. For example, type ping 192.168.1.1 and press Enter.The result should be something like this:Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Ping statistics for 192.168.1.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 4ms, Maximum = 5ms, Average = 4ms
If the ping is successful and you see results similar to the results above, but you can’t connect to the Internet on your PC, there may be a problem with your modem or Internet service provider (ISP).

#Method 5 : Check your network adapter to fix no internet secured

1. Go to Control Panel >Network and InternetNetwork Connections

2. Choose your wifi connection, right-click and select Properties

3. In the Wi-Fi Properties, in the “This connection uses the following items:” tab, you should check the following options:

  •     Client for Microsoft Networks
  •     File and Printer Sharing for Microsoft Networks
  •     Link-Layer Topology Discovery Mapper I/O Driver
  •     Internet Protocol Version 4 (TCP/IPv4)
  •     Reliable Multicast Protocol
  •     Internet Protocol Version 6 (TCP/IPv6) ( You should uncheck it )
  •     Link-Layer Topology Discovery Responder

How to fix no internet secured windows 7810

#Method 6 : Check your driver of PC or laptop to fix no internet secured

You can use DriverEasy to update your driver .

#Method 7 : Disable and then enable your connect to fix no internet secured

If it doesn’t change for the moment, try to disable and then enable your connect .

You go control panel => Network and Internet => Change adapter setting =>disable connect then reconnect

disable connect.jpg

#Method 8 : Other steps to try on your router to fix no internet secured

Here are some things to check and try with your router if you’re at home and having trouble getting connected.

  • If you don’t see the network name, sign in to your router and check to see if it’s set to broadcast the network name.
    1. Connect your PC to your router using an Ethernet cable.
    2. Open your web browser and type the IP address for your wireless router. (For example, 192.168.1.1 or 172.16.0.0—check the documentation for your router to find the default IP address.)
    3. Sign in with your user name and password, then make sure an option labeled Enable SSID BroadcastWireless SSID broadcast, or something similar is turned on. This setting is often on a Wireless Settings page.
  • Check to see if your Wi-Fi network uses Media Access Control (MAC) address filtering for security. If it does, you’ll need to add the MAC address for your PC to the access list on your router before you can connect.
    1. Select the Start button. Type cmd in the search box and right-click cmd in the list. Select Run as administrator, and then select Yes.
    2. At the command prompt, type ipconfig /all.Write down the address that appears next to Physical Address for your wireless network adapter. This is the address you’ll need to add to the access list on your router.

    To add the MAC address to the access list on your router:

    1. Open your web browser and type the IP address for your wireless router. (For example, 192.168.1.1 or 172.16.0.0—check the documentation for your router to find the default IP address.)
    2. Sign in with your user name and password, then look for a setting that says MAC Address Filter or something similar.
    3. Add the MAC address you wrote down for your PC to the access list and save your changes.
    On your PC, try to connect to the Wi-Fi network again.

I hope it works for you to! 🙂

Tag : How to fix no internet secured windows xp , How to fix no internet secured windows 7 , How to fix no internet secured windows 8 , How to fix no internet secured windows 8.1 , How to fix no internet secured windows 10

Windows Modules Installer Worker High CPU Usage FIX

What Is Windows Modules Installer Worker?

This system process “enables installation, modification, and removal of Windows updates and optional components”, according to its service description.

Windows 10 automatically installs operating system updates via Windows Update, so this process is likely just installing updates in the background. However, if you choose to uninstall an update or add or remove an optional Windows feature, the Windows Modules Installer Worker process will also need to do some work.

While the process is named Windows Modules Installer Worker on the normal Processes tab in Windows 10’s Task Manager, its file name is TiWorker.exe, and you’ll see that displayed on the Details tab.

Windows Modules Installer Worker

However, Sometimes this process gets messed up and results in a high CPU usage. Also, sometimes it reaches >50% of CPU usage. Consequently, this process causes load on the system, thus hanging or freezing all the other processes. Slowed down PC or Frozen computer are the symptoms of this issue. Unlike other common errors, restarting the PC won’t work in this case. You must resolve this issue manually as it is not able to fix by itself.

How to Fix Windows Modules Installer Worker- High CPU Usage

Preventing Windows Modules Installer Worker from working is not a solution to its high CPU usage problem. As updates are essential. Instead, I have compiled 3 working and simple solutions for you. You don’t need a bag of full of computer knowledge or tools to use them. Just follow the step-wise guide that I’m providing. Let’s move further to the solutions for Windows Modules Installer Worker high CPU usage problem.

#Method 1 : Set Windows Update to Manual

This method works on the principle of switching the Windows Updates utilities from Automaticto Manual. So that it stops demanding power continuously. The major drawback of this method is that you have to keep looking for any Windows updates manually (weekly/monthly). Follo these steps in order to use this solution:

Step-1: Firstly, press the Windows + R key simultaneously in order to trigger the Run dialog box. Type services.msc in it and click Ok.

services msc

Step-2: In the Services window, locate and double-click on Windows Modules Installer. Its Properties window will open up.

Windows Modules Installer

Step-3: In the resultant window, go to Startup type and change it to Manual. Startup type will be present under the General tab. Afterwards, click on Apply and then Ok.

General tab.

Step-4: Now go back to the Services window again. This time double-click on Windows Update. Its Properties window will open up just like earlier.

Windows Update

Step-5: In the resultant window, go to Startup type and change it to Manual. Then click on Apply and then Ok.

Startup type

 

Step-6: Restart your PC. Check if your problem is solved by accessing the Task Manager (Start Menu-> Task Manager).

After the successful application of this method, Windows Modules Installer Worker CPU usage would return back to its normal value. This is the most accurate and easy method to resolve this issue.

#Method 2 : Use Windows Update Troubleshooter to Fix High CPU usage

This method uses the WindowsUpdateDiagnostic.diagcab tool (Windows Update Troubleshooter) to fix all the Windows Updates related issues. The Troubleshooter is easy to use and is able to rectify the Windows Modules Installer Worker high CPU usage problem in few minutes. Follow these steps in order to use this solution:

Step-1: Download Windows Update Troubleshooter from here.

Step-2: After setting it up, run the WindowsUpdateDiagnostic.diagcab tool.

Windows Update Troubleshooter

Step-3: The tool will resolve issues by checking registry keys and certain other things. Therefore, the process may take some time. Have patience and wait until the process is complete.

Windows Update Troubleshooter

Step-4: After the “Troubleshooting has completed” message appears on your screen, click on the Close button.

Step-5: Restart your computer. Check if your problem is fixed by accessing the Task Manager(Start Menu-> Task Manager).

After you use Windows Update Troubleshooter properly, it will fix all the Windows Updates related problem including, Windows Modules Installer Worker high CPU usage. The computer will start working normally.

#Method 3 : Scan virus

Viruses or malicious programs can be the cause of unusually high CPU errors caused by TiWorker.exe. So to fix the problem, you can use antivirus programs to find and remove viruses and malicious programs on your computer and to fix the error.

#Method 4 : Reduce the TiWorker process priority

Step-1 : Ctrl + Shift +Esc => Task Manager

Task Manager

2.You click tab : Details

tab-detail.png

3.You right click on TiWorker.exe, ,choose Set priority => Low

Set-priority.png

Tag :windows modules installer worker windows 10 , windows modules installer worker high cpu usage , tiworker exe windows modules installer worker

Anytrans License Code 2018 For Windows

Anytrans License Code from iMobile is a video & music conversion app and transfer software for iOS Devices. With renewed design and a new pair of features, AnyTrans allows you to manage your iPhone, iPad and iPod touch content in a significantly easier way, saving you both time and hard work.

Anytrans License Code 2018 For Windows

Features of Anytrans

  • Always put your photographs in the right place – Use AnyTrans to enrich or simplify your image library with a major window and only your chosen photos. It’s the most comfort way to
  • coordinate, enjoy and share the occasions you snapped. Presume, through just a few clicks, you’ll be able to transfer thousands of photographs or even your complete library between iPhone, Apple iPad tablet and computer, all at once.
  • It makes any videos properly fit on your display, automatically.
  • Ultra-modern design, super-fast music syncing speed, in addition to a nature of made-only-for-Apple-device, AnyTrans opens up a whole new way to manage your iPhone, iPad, iPod and iTunes media in a way you even think impossible.
  • Backup & identical copy not only your programs, but also everything inside – It’s a neat interface, convenient options, and many behind-the-scene technologies which make AnyTrans instantly elevate your App managing experience. Not any matter you want to install or uninstall an app, create iPhone app back up or carry through data migrations, AnyTrans will get it done, just at one go.

HOW TO REGISTER:

1 First of all of all Download AnyTrans Setup which is given above.

Installment payments on your Install It and Start this software as normal.

  1. Use iMobie AnyTrans license code to Activate.
  2. Hold out a minute for the activation reply.

All done Enjoy!

Anytrans License Code 2018

FKSUEH-FJKSIE-FJKLDIE-FKDJEIFJD

ID: DFI49DU48

Anytrans License Code 2017

FJKSIE-FJDFJ-FJDIEJ-FDJDUE-FJDIE

ID: JFIE9D

7 Best Windows Photo Viewer Alternatives For Windows 10

Why Replace “Photos” App on Windows 10?

Microsoft replaced our beloved “Windows Photo Viewer” in 2015 edition of Windows 10. A lot of people were confused, including me. As “Windows Photo Viewer” was a powerful and amazing software that fulfilled every requirement of the users who used it. The software was replaced by the “Photos” app. People did not accept this change wholeheartedly.

According to the reviews collected by different users, they find the “Photos” app:

  • a basic software that lacks some needed features.
  • only good enough to view pictures, and not tweak them.
  • heavy power consuming and loads pictures relatively slow.

Windows Photo Viewer is the built-in app for viewing your photos in Windows. Almost all formats of images are supported by Windows Photo Viewer. But in Windows 10, Microsoft has confused its users by providing another photo viewer called Photos, which is not liked by users as they are used to with Windows Photo Viewer.

7 Best Photo Viewer for Windows 10

1.XnView

Best Photo Viewer for Windows 10

XnView is a fast image viewer third party tool that provides you many features as like Windows Photo Viewer provides. You can use it in a portable version also. The image rendering quality is very good and fast as compared to IrfanView, but it’s most of the features are same of IrfanView viewer.

XnView supports more than 500 file formats. Therefore it is able to open almost any type of image that you have on your PC. The image rendering quality is very good and fast and it also has a multi-lingual user interface. This third-party tool is a lot like IrfanView. You can use it in a portable version too. Some other great features include viewing images in several ways, such as standard Thumbnail view or FullScreen view.

XnView allows you to process your images with an arsenal of editing tools:

  • Resize, Rotate, Crop
  • Lossless Rotate & Crop (jpeg)
  • Adjust Brightness, Contrast, …
  • Auto Levels, Auto Contrast
  • Modify Colors depth & palette
  • Apply filters & Effects

To download XnView you visit here : https://www.xnview.com/en/xnview/

2.Nomacs

Nomacs

Nomacs is a free and open source photo viewer with clustered of features and functions. You can use it on almost every Operating System. It supports almost all image formats including RAW and PSD images. Nomacs makes you able to view the metadata, thumbnails, and histogram of your images.

Nomacs includes image manipulation methods for adjusting brightness, contrast, saturation, hue, gamma, exposure. It has a pseudo color function which allows creating false color images. A unique feature of nomacs is the synchronization of multiple instances. With this feature you can easily compare images by zooming and/or panning at the exactly same position or even by overlaying them with different opacity. Nomacs is licensed under the GNU General Public License v3 and available for Windows, Linux, FreeBSD, Mac, and OS/2. It is free for private and commercial use.

As like Windows Photo Viewer, Nomacs supports almost all types of image formats. See your multiple images together in a Slide Show with Nomacs. And you can edit your photos with basic editing tools like cropping, rotating and resizing as like you can do with Widnows Photo Viewer.

To download Nomacs you visit here : https://nomacs.org/download/

3.IrfanView

IrfanView is a photo viewing and editing software that probably all of the advanced users are aware of. This software worked great on the older versions of Windows and performs amazingly on the newer versions as well. The owner has improved the software with his immense hard work completely free of cost. The major specialty of IrfanView is its vast range of options and preferences making it a very configurable software.

To download IrfanView you visit here : https://www.irfanview.com/

4.FastStone Image Viewer

FastStone Image Viewer

FastStone Image Viewer is a fast, stable and reliable image viewer, image browser, image editor and image converter. It is a freeware and open source tool. FastStone supports a large number of image formats. It has basic editing tools that can help you on cropping, rotating, resizing your images. It also removes the red eye from your images. Drag/Drop and Copy/Move feature is available for users convenience. Versatile screen capturing facility is available in FastStone Image Viewer. Different effects and transitions are provided in this viewer. You can apply multilevel undo or redo with your images.

To down load you FastStone  visit here : http://www.faststone.org/FSViewerDownload.htm

5.Picasa Photo Viewer

Picasa Photo Viewer

The Picasa Photo Viewer is a fast, stable and cool looking image viewing software for Windows. This Photo Viewer has a similar feeling to a media player as it is way too different than a simple picture gallery. You can press Enter key on your keyboard to see any image in fullscreen mode, and you can start a slideshow also with just a single click.

It is also packed with the basic image editing tools that may fulfill the needs of almost all the users. One drawback of using this software now is that the image upload feature will not be supported as Google has shut down Picasa’s web service

To download Picasa Photo Viewer you visit here : https://picasa.en.uptodown.com/windows

6.Imagine

Imagine

Imagine is very fast and lightweight photo viewer among all. It is freeware third party image viewer. It supports a large number of image formats. You can view detailed information of your image files. It supports ZIP, RAR, 7Z, ALZ, HV3, CBZ, CBR, and CB7 files. Imagine has multilanguage support.

Both 32bit nad 64-bit versions are available. It helps you to capture your screen, create animations. Batch conversion is also supported. View your images together in a slideshow with Imagine.

To download Imagine  you click here

7.FreshView 

FreshView

Fresh View gives you the ability to organize and view multimedia files (images, audio, video). Watch movies, listen to music, and view graphics in a slide show. Image files in a folder can be displayed using a number of views, including a thumbnail view that lets you quickly see what your images are without having to open them.

You can convert graphics from one type to another, print, and even create an HTML album. This easy-to-use software supports 86 different formats (more and more added regularly).

To download Fresh View you click here

Tag : best photo viewer for windows 10 , best image viewer windows 10 , picture viewer for windows 10

How to Fix “Encrypt Contents To Secure Data” Option Grayed out in Windows 10

Windows 10 comes with Encrypted File System (EFS) which allows users to encrypt their data in a particular folder or drive. This is especially useful when you want to keep your data private only such that it is accessible from your Windows account only. No one else will be able to open the encrypted files or folders.

Encrypt Contents To Secure Data

EFS is available for all editions of Windows 10 except Windows 10 Home edition. The EFS option is very easy to get access to by just going to Properties of a particular folder and check a check-box that says “Encrypt Contents To Secure Data” in the Advanced tab.

Sometimes, this option is grayed out and you cannot encrypt data in this scenario. This issue is usual and can occur to anyone, as it arises due to misconfigured of registry values.

If “Encrypt Contents To Secure Data” option is grayed out, the following solutions may be helpful in making it work again to start encrypting your personal and private data.

#Method 1 : Enable EFS using Command line

You can use Windows Command line to make the encryption option available for you for any of folders on your machine. You just have to run a simple and easy command. And your problem will resolve quickly. To do this, go with few below steps.

  • Press Windows + R, then type services.msc.
  • Double-click on Encrypting File System (EFS), under General change the Startup type to Automatic.
  • Hit Apply, then OK.
  • Restart your PC.

#Method 2 : Enable EFS Using Windows Registry

The encryption option may be grayed out because some registry values are not set properly. To resolve this, follow the steps below.  ( Ensure that you’re logged in as administrator. )

1.Open Run dialog from the Start Menu and type “regedit” in it to open Registry Editor window.

regedit

Registry Editor window

2.Now move into following entry in the Registry Editor window.

HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\FileSystem

2-3.jpg

3.Expand File System key to right-hand window, and look for the key named NtfsDisableEncryption. Double click on it, and set its value to 0.

NtfsDisableEncryption

4.Save the settings and close all open windows. Go back to “Properties\Advanced\Advance Attribute” option of your required folder which you want to encrypt. The option of encryption will no longer be grayed out.

Advance Attribute

 

The solutions are simple and easy to use. You can pick any solution as both are tested and verified. Don’t put your data at risk, and start securing it immediately by encrypting sensitive and important data.

Tag :Encrypt Contents To Secure Data , encrypt contents to secure data greyed out windows 10 , unable to uncheck encrypt contents to secure data